DeSCRJPTion:
Baudcom’s BDTR-GB-PxRC Copper Small Form Pluggable (SFP)transceivers is high performance, cost effective module compliant with the Gigabit Ethernet and 1000- BASE-T standards as specified in IEEE 802. 3-2002 and IEEE 802.3ab, which supp- orting 1000Mbps data- rate up to 100 meters reach over unshielded twisted-pair category 5 cable. The module supports1000 Mbps full duplex data-links with 5-level Pulse Amplitude Modulation (PAM) signals. All four pairs in the cable are used with symbol rate at 250Mbps on each pair. The module provides standard serial ID information compliant with SFP MSA, which can be accessed with address of A0h via the 2wire serial CMOS EEPROM protocol. The physical IC can also be accessed via 2wire serial bus at address A0h.
Features:
Line Frequency
Tx Output Impedance
Rx Input Impedance
08
22
2016
1000Base-T SFP Transceiver 光模块 通信
来源:[上海伯唐通信设备有限公司]
联系人：谢先生
手机：17701868283
电话：021-37709251
传真：021-37709302
QQ：2758037043
Email：2758037043@qq.com
地址：上海上海市闵行区闵行区联明路389号
品牌：
价格：60.00
元/只
供应地：上海上海市
产品型号：
Interface:
All high-speed signals are AC-coupled internally.
Table 3. High-speed electrical interface, transmission line-GBIC
High-Speed Electrical Interface Transmission Line-GBIC
Parameter
Symbol
Min
Typ
Max
Units
Notes/Conditions
fL
125
MHz
5-level encoding, per IEEE 802.3
Zout,TX
100
Ohm
Differential, for all Frequencies between 1MHz and 125MHz
Zin,RX
100
Ohm
Differential, for all Frequencies between 1MHz and 125MHz
High-speed electrical interface, host-GBIC
Table 4. High-speed electrical interface, host-GBIC
High-Speed Electrical Interface, Host-GBIC
Parameter
Symbol
Min
Typ
Max
Units
Notes/Conditions
Single ended data input swing
Vinsing
250
1200
mV
Single ended
Single ended data output swing
Voutsing
350
800
mV
Single ended
Rise/Fall Time
Tr,Tf
175
psec
20%-80%
Tx Input Impedance
Zin
50
Ohm
Single ended
Rx Output Impedance
Zout
50
Ohm
Single ended
General Specifications
Table 5. General specifications
General
Parameter
Symbol
Min
Typ
Max
Units
Notes/Conditions
Data Rate
BR
10
1,000
Mb/sec
IEEE 802.3 compatible.
See Notes 2 through 4 below
Cable Length
L
100
m
Category 5 UTP. BER <10-12
Notes:
1. Clock tolerance is +/- 50 ppm
2. By default, the BDTR-GB-P is a full duplex device in preferred master mode
3. Automatic crossover detection is enabled. External crossover cable is not required
4. 1000 BASE-T operation requires the host system to have an SGMII interface with no clocks, and the module PHY to be configured per Application Note AN-2036. With a SERDES that does not support SGMII, the module will operate at 1000BASE-T only.
Environmental Specifications
Table 6. Environmental specifications
Environmental Specifications
Parameter
Symbol
Min
Typ
Max
Units
Notes/Conditions
Operating Temperature
Top
0
85
°C
Case temperature
Storage Temperature
Tsto
-40
85
°C
Ambient temperature
